#What is cold formed steel framing how to#
#What is cold formed steel framing registration#

Sheathing braced design requires that identical sheathing is used on each side of the wall stud, except the new AISI S240 standard Section B1.2.2.3 clarifies that for curtain wall studs it is permissible to have sheathing on one side and discrete bracing for the other flange not spaced further than 8 feet on center.В The wall stud is connected to the top and bottom tracks or supporting members to provide lateral and torsional support and the construction drawings should note that the sheathing is a structural element. CFS Curtain Wall Stud Steel Clip and Bridging Bracing

#What is cold formed steel framing how to#

AISI S211 Section B1 and the Commentary discuss the design method and assumptions and demonstrate how to determine the sheathing bracing strength. AISI S211 prescribes a maximum nominal stud axial load for gypsum board sheathing with fasteners spaced no more than 12 inches on center. Due to this limitation, the Designer has to use a steel braced design for most practical situations. This design method is based on an assumption that the sheathing connections to the stud are the bracing points and so itвЂ™s limited by the strength of the sheathing fastener to stud connection. Sheathing braced design has limitations, but it is a cost effective method of bracing studs since sheathing is typically attached to wall studs. One is sheathing braced design and the other is steel braced design. There are two methods for bracing CFS studs as prescribed by the American Iron and Steel Institute (AISI) Committee on Framing Standards (COFS) S211 вЂњNorth American Standard for Cold-Formed Steel Framing вЂ“ Wall Stud DesignвЂќ Section B1. Bracing is required to resist buckling due to axial or out-of-plane lateral loads or a combination of the two. Without proper consideration of bracing, excessive buckling or even failure could occur. While consideration of bracing is important for any structural element, this is especially true for thin, singly symmetric cold-formed steel (CFS) framing members such as wall studs. Louis BRACE FOR IMPACT! Bracing Design for Cold-Formed Steel Studs Wei-Wen Yu, floor joists, girts, panels., purlins, Simpson Strong-Tie, wall studs Leave a comment on 24th Short Course on CFS Structures: October 27-29 in St. Author Jeff Ellis Posted on AugCategories Academia, Technology Tags cold-formed steel, cold-formed steel framing, decks, Dr. For more information and to register, click here.

#What is cold formed steel framing registration#

Advance registration is requested by October 10, 2015. It is eligible for 2.4 Continuing Education Units (CEUs).

The course will address such topics as design of wall studs, floor joists, purlins, girts, decks and panels. Louis 24th Short Course on CFS Structures: October 27-29 in St. Wei-Wen Yu, floor joists, girts, panels., purlins, Simpson Strong-Tie, wall studs Leave a comment on 24th Short Course on CFS Structures: Author Jeff Ellis Posted on AugAugCategories Academia, Technology Tags cold-formed steel, cold-formed steel framing, decks, Dr. Wei-Wen YuвЂ™s book Cold-Formed Steel Design (4 th Edition) will be a reference text. The course is based on the 2012 AISI North American Specification for the Design of Cold-Formed Steel Structural Members and the 2012 North American Standards for Cold-Formed Steel Framing. Lectures will be given by industry-recognized experts Roger LaBoube, Ph.D., P.E., and Sutton Stephens, Ph.D., P.E., S.E.

This three-day course is for engineers who have limited or no experience designing with cold-formed steel (CFS), as well as those with experience who would like to expand their knowledge of cold-formed steel structural design. The course will be held on October 27-29, 2015 at the Drury Plaza Hotel at the Arch in St. Simpson Strong-Tie is sponsoring the 24 th Short Course on Cold-Formed Steel Structures hosted by the Wei-Wen Yu Center for Cold-Formed Steel Structures (CCFSS).